This took a LOOONG hard think.
Common sense tells me the fuel pump has to situated somewhat lower than the bottom of the fuel tank, ensuring a flooded suction at all levels of the fuel tank - dry, full and in-between. Taking a look at inside the rear compartment there is not a lot of space where such an item can be placed. Bear in mind there is a lot of suspension arms and movement in there. Lots of builders resort to an in-tank pump/swirl pot/sender/filter arrangement which is actually a very cool solution (But costly).
I opted to place the pump vertically next to the fuel tank on the left hand side bolted on to inside the aluminium skin. From the outside you see only 2 bolt heads and the wheel covers them anyway. It looks good and usually if it looks good it generally is good (but not always). The fuel feed comes from the bottom of the tank to the pump intake, out the pump at the top, over the wheel arch and down to the filter before entering the delivery pipe to the front of the car.
My only gremlin is vibration and to mitigate that I am going to use a great gob of silicone sealer to anchor the bracket to the steel tube member. The fuel pump bracket is a mangy piece of engineering that needs to be replaced with something waaaaay more solid. It relies on two pop rivets and offcut aluminium sheeting. I think this is an item for my "Fix This Before You Start Driving" list. I have got a bracket engineered in my head but it is going to cost a bit. Nice plug for Mechanix gloves, don'cha think?
Tuesday, 12 June 2012
Monday, 11 June 2012
The Dashboard
Yesterday I installed the gauges and switches, today I wired them up and tested them for continuity and earthing. The switches remain unconnected, there are some issues with regard to the wiring colouring. I must just check the wires through the fusebox to the source, and the ammeter is not connected either.
I also installed the wiper motor, ignition switch and the driver's seat runners. The ignition switch was a bit of a struggle as I had to loosen the upper portion of the steering column so that the lock in the switch would engage the slot in the column.
At the back I fitted the fuel tank sender unit which only required a minor relieving of the hole to insert.
I also installed the wiper motor, ignition switch and the driver's seat runners. The ignition switch was a bit of a struggle as I had to loosen the upper portion of the steering column so that the lock in the switch would engage the slot in the column.
At the back I fitted the fuel tank sender unit which only required a minor relieving of the hole to insert.
Saturday, 9 June 2012
The Dashboard and Instruments
The car came with an un-upholstered dashboard, so I have decided I want it done in a charcoal vinyl.
There is a small upholstery shop here in Mokopane, they had everything I needed.
Armed with thin sponge, the vinyl, contact glue and razor blades I roughly cut out the shape of the dash in sponge and glued that onto the dash. Then I cut out the instrument holes and trimmed the sponge with a razor blade.
Next move was to cut out an identical shape but a little larger, in vinyl. I did not glue the vinyl to the sponge, preferring to just stretch it over and glue it around the edges, behind the dash. You can see the bead stretching over the top of the dash.
As soon as I had enough glued on, I couldn't resist fitting a gauge to see the effect. I carefully cut a hole smaller than the instrument hole so that the gauge clamps the vinyl. The effect looks good! That's the ammeter by the way.
And the final product surprised even me. There is a gap where the speedo should be. The factory supplied me with another rev counter instead. That is going to be swopped out soon. I also have an issue with the dip switch, the action isn't what I'd expect - push to make, push to break. This is a momentary switch which is all wrong. Tomorrow I am going to try connect up what I can.
There is a small upholstery shop here in Mokopane, they had everything I needed.
Armed with thin sponge, the vinyl, contact glue and razor blades I roughly cut out the shape of the dash in sponge and glued that onto the dash. Then I cut out the instrument holes and trimmed the sponge with a razor blade.
Next move was to cut out an identical shape but a little larger, in vinyl. I did not glue the vinyl to the sponge, preferring to just stretch it over and glue it around the edges, behind the dash. You can see the bead stretching over the top of the dash.
As soon as I had enough glued on, I couldn't resist fitting a gauge to see the effect. I carefully cut a hole smaller than the instrument hole so that the gauge clamps the vinyl. The effect looks good! That's the ammeter by the way.
Friday, 8 June 2012
Applying for an Importers Code
Last week Fedex informed me the first of my parts shipments for the engine had arrived and could I please supply them with an importers code.
Turns out that any import worth more than R20,000 SARS requires you to register as an importer. So I fill in the DA185 to register and off I go to Customs and Excise at Polokwane International and hand in the docco. They supply me with a receipt showing I have applied, which is all I need to get my shipment released. I scan that, and e-mail it to Fedex.
This means I can get moving on the engine next week.
Funny thing about Polokwane International, there must have been around 40 staff moving around the building sweeping, cleaning windows, doing office work, but my bakkie was the ONLY vehicle in the car park. Not ONE single passenger in the building!!!
Turns out that any import worth more than R20,000 SARS requires you to register as an importer. So I fill in the DA185 to register and off I go to Customs and Excise at Polokwane International and hand in the docco. They supply me with a receipt showing I have applied, which is all I need to get my shipment released. I scan that, and e-mail it to Fedex.
This means I can get moving on the engine next week.
Funny thing about Polokwane International, there must have been around 40 staff moving around the building sweeping, cleaning windows, doing office work, but my bakkie was the ONLY vehicle in the car park. Not ONE single passenger in the building!!!
Monday, 4 June 2012
Clutch and Brake Master Cylinders
I get home from work and reward myself with a bit of something different.
I haul out the cylinder kit and then sit down next to the car and visualise how these are supposed to fit. OK here are two identical cylinders - these must be the brakes front and rear, and this one must be the clutch. Then I see that the castings have got a nasty seam running across the hole, so out with the Dremel and I grind these off to give a nice flat surface for the nuts to torque on to. Then swop out the fitted con-rods for the supplied ones, replacing the grease in the process. Grease up the shaft, replace the boot and we are good to go.
The cylinders go in no problem, on go the hoses, and I connect these to the mount plate and to the front and rear hydraulic lines. Job done!
I haul out the cylinder kit and then sit down next to the car and visualise how these are supposed to fit. OK here are two identical cylinders - these must be the brakes front and rear, and this one must be the clutch. Then I see that the castings have got a nasty seam running across the hole, so out with the Dremel and I grind these off to give a nice flat surface for the nuts to torque on to. Then swop out the fitted con-rods for the supplied ones, replacing the grease in the process. Grease up the shaft, replace the boot and we are good to go.
The cylinders go in no problem, on go the hoses, and I connect these to the mount plate and to the front and rear hydraulic lines. Job done!
Sunday, 3 June 2012
The Sideshafts, Upper Wishbones and Anti-Roll Bar
Sunday morning and we brace ourselves for the upper wishbones (lousy pun). The day before I had seen the the right upper would go in pretty easily, but the left was going to give us trouble.
And so it proved. Measuring up there was no clearance at all for a 4th washer. Or you could do 2 whole washers and 2 1/2 thickness washers. No matter which way you cut it it was going to be a bear. So out with the grinder. Try again, we bash bolts through and discover we have irrepairably damaged the thread of the rear bolt.
Damn. I'll get one at the local engineering shop.
So in a fit of pique I fit the anti-roll bar (easy-peasy) and the side shafts (also easy-peasy, especially with an angled impact ratchet).
Note at this time NOTHING has been torqued up.
I have a nagging feeling the hubs are sticking out too far...... That's because I am thinking the diff I have is too wide between the flanges (30cm) leaving the sideshafts too long. As soon as I get the rear uprights I will know.
And so it proved. Measuring up there was no clearance at all for a 4th washer. Or you could do 2 whole washers and 2 1/2 thickness washers. No matter which way you cut it it was going to be a bear. So out with the grinder. Try again, we bash bolts through and discover we have irrepairably damaged the thread of the rear bolt.
Damn. I'll get one at the local engineering shop.
Note at this time NOTHING has been torqued up.
I have a nagging feeling the hubs are sticking out too far...... That's because I am thinking the diff I have is too wide between the flanges (30cm) leaving the sideshafts too long. As soon as I get the rear uprights I will know.
Saturday, 2 June 2012
Fitting the Handbrake, Differential and the IRS
I suppose the moment of truth has arrived - time to fit the handbrake, differential and the independent rear suspension. Note that at this time I have NO instructions on how to do this, only pictures from other build diaries. Luckily a lot has been written/blogged about this.
It is the second build weekend and because Alastair is here I need him to help me get some of the nasty and heavy work out of the way.
Up early as I want to maximise the weekend so I leave Al to sleep and get on with the handbrake. I've studied the setup all week and my only puzzle is how to fit the main cable. I hit on the idea of feeding the handle end of the cable through its hole, then pulling the wire all the way out backwards and feeding that through the hole on the engine side, and hey it nearly works the damn hole is just a tad too small for the snout. Out with the die grinder and now it goes in snug. Fit the circlip and job done. The rest is a doddle, "D" plate, pins, cotters left and right cables, a smidgeon of grease and it is all good.
Just in time for the shops to open....
I hurry off to Autozone to pick up some new oil seals for the diff, some LM grease, GL-4 hypoid oil and some other odds and sods.
Get home, and first thing we empty the diff of oil. Hypoid oil has got to be the most evil concoction ever, well, concocted. Clean Green? You might as well use shampoo...
Using my trusty impact wrench we sound like a NASCAR pit and off comes the back cover. Where are these circlips so I can remove the pinions.....?
No circlips, in fact the inside of the diff bears NO resemblance to what the manual shows. The cage is completely closed except for 2 small apertures. I see no way I am going to disassemble this bad boy so I admit defeat, cut a new gasket, bolt her up. Its just as well it wasn't leaking anyway.
With the bitter taste of defeat in our mouths we decide to do the lower wishbones. To our surprise these go in relatively easily, because I hit on the idea of sharpening the washers on one edge to "get a foot in the door" so to speak.
We break for lunch. Now for the diff.
When I get back I realise that to fit the diff we have to remove the rear aluminium mounting plate. OK that means removing the lower bolt for the left wishbone, undoing the ally plate and "V" struts, and swinging it upward out of the way. No problem.
Smartarse. Out she comes for an oil fill. One litre of GL-4 wotsisname oil later and in the diff goes again, we do up the ally plate and the rear mounts on the diff.
Then we re-install the left lower wishbone. By this time it is dark. Off to the "Dros" and we watch the Stormers thump the Bulls. Great!!!
What an end to the day!!!!
It is the second build weekend and because Alastair is here I need him to help me get some of the nasty and heavy work out of the way.
Up early as I want to maximise the weekend so I leave Al to sleep and get on with the handbrake. I've studied the setup all week and my only puzzle is how to fit the main cable. I hit on the idea of feeding the handle end of the cable through its hole, then pulling the wire all the way out backwards and feeding that through the hole on the engine side, and hey it nearly works the damn hole is just a tad too small for the snout. Out with the die grinder and now it goes in snug. Fit the circlip and job done. The rest is a doddle, "D" plate, pins, cotters left and right cables, a smidgeon of grease and it is all good.
Just in time for the shops to open....
I hurry off to Autozone to pick up some new oil seals for the diff, some LM grease, GL-4 hypoid oil and some other odds and sods.
Get home, and first thing we empty the diff of oil. Hypoid oil has got to be the most evil concoction ever, well, concocted. Clean Green? You might as well use shampoo...
Using my trusty impact wrench we sound like a NASCAR pit and off comes the back cover. Where are these circlips so I can remove the pinions.....?
No circlips, in fact the inside of the diff bears NO resemblance to what the manual shows. The cage is completely closed except for 2 small apertures. I see no way I am going to disassemble this bad boy so I admit defeat, cut a new gasket, bolt her up. Its just as well it wasn't leaking anyway.
With the bitter taste of defeat in our mouths we decide to do the lower wishbones. To our surprise these go in relatively easily, because I hit on the idea of sharpening the washers on one edge to "get a foot in the door" so to speak.
We break for lunch. Now for the diff.
So we loosen the attachment bolts, loosen the "V" struts, remove those and we lift in the diff. The front goes in fine but the diff will not lower into position. Quick, check the handbrake. We see that a stiffening rib on the bottom of the diff housing is resting on the handbrake "D" plate. Out she comes. Break out the grinder and I have at the casing. Looks like I've taken off enough - try again. Nope. Out she comes and this is where I get medieval on its ass and grind a whole lot more off. Try again. OK the handbrake works but somewhere in its arc it fouls the diff again. Out she comes. By this time I am getting a bit tired of this so I REALLY go to town on the offending ribs. In she goes. This time it clears and lowers into position. Do up the front mounts which are M12. Get to the middle ones and find that the mounts on the car are M10, the threaded hole in the diff case is M12. So I need some M12 bobbins and new bolts. By this time Alastair has named this the "Diff from Hell" as so far it hasn't ticked ANY of the right boxes and he is wanting to know was it actually a Ford Sapphire I took this off? Oh, and by the way did you fill it up with oil before we fitted it? 'Cause with this plate in the way.....
Smartarse. Out she comes for an oil fill. One litre of GL-4 wotsisname oil later and in the diff goes again, we do up the ally plate and the rear mounts on the diff.
Then we re-install the left lower wishbone. By this time it is dark. Off to the "Dros" and we watch the Stormers thump the Bulls. Great!!!
What an end to the day!!!!
Subscribe to:
Posts (Atom)