Monday, 11 November 2013

Fiddling about

Things look to be moving slowly right now but what with the summer heat it is getting to be really rare to find a suitable day on the weekend where the weather is good AND I don't have something else to do that does not involve either the kids, the wife or shooting.

But enough excuses.

Last Saturday I buckled down and cut out a cover plate for the rear end of the selector tunnel. Normally the T-9 box has a metal cap or dust cover that blocks the oval end of the gear selectors. My box had no such part, the previous owner electing to use copious amounts of silicon sealer instead.

I did not have any ally plate I could use so I improvised with an old breadboard made of polyethylene. It was pretty thin and easy to cut. Simple enough to do and I sealed the edges with RTV silicone.
 
 
 
Being very happy with that my next move was to sort out the EMS wiring routing. The Alphamax system seems to have way too long leads terminated by extremely rare and spendy looking connectors, so I took the coward's way out and looped up the excess lead, bound those with lots of cable ties and hid them under the heater box. Of course there will be no heater.
 
Other leads were fastened in place with cable clips and Rivnuts

 
Now I must sort out transport to the wiring specialists.
 

Monday, 5 August 2013

I Got your Number!

This weekend I tackled the number plate and the illumination thereof. I bought these really neat little LED lamps and painted them red. Then lined up everything and drilled the holes, set the rivnuts and....



Then it was time to get adventurous with a small file and sort out the Lambda sensor which could not be installed without cutting away some of the exhaust guard. Very stressful handiwork!


My next problem lies in routing the sensor cable - I dont want to route it along the body to the exhaust header port, that will need putting small holes in the body for P clips. The other alternative is routing it along the exhaust pipe - neat but liable to melt the cable! Or straight up the body to the scuttle - ugly!!!

I am thinking of cutting a neat hole in the body with a chassis punch and putting in a weatherproof grommet, leaving the outside run to 3-4 inches at most. I found that DEI make a neat flexible heat shield tube for just such eventualities and I may just give them a call.


Thursday, 1 August 2013

Zorsts.....NEARLY there

Today I fitted the headers and the pre-assemble muffler. The headers took a bit of manipulation but luckily I had done this once before so I knew the procedure front and back. First fit the two outer headers, then the siamese centre pipes. I sourced another manifold gasket because Lord alone knows what happened to the last one. I also had to work around the throttle cables.



Next was the collector pipe which is a cute 4 into 1. I was clever enough to just  loosen the manifold bolts enough to give me some wobble room. With the aid of a large wooden mallet that went on with minimum fuss. You'll see some springs there I had to buy because the OEM items are keeping the manifold gasket company somewhere.


Nothing daunted I proceeded to fit the muffler and connector pipe, these were a perfect fit and matched the body mount to the millimeter!!! Unfortunately one of the M8X1.0 Metric fine nuts that goes with the rubber vibration mount has gone astray with the gasket etc etc.



I then loosely fitted the red exhaust guards, and discovered that the front guard is going to need a bit of modification because the Lambda sensor that fits into it fouls the guard.

I think this is going to be a little cracker of a car when she is done!!!


 






Monday, 29 July 2013

Zorsts.......It's a Wrap!!!

Back again after a long gap, I've been busy sorting out the last maor component install, namely the exhaust system. When I left them, they had been painted heat resistant black, and I had decided to wrap the headers in some space age lava rock weave. I spent a bit of time waiting for the stuff, it is called DEI titanium exhaust wrap, and the local agent is Michael Moolman. At any rate he came through with the merch. I bought 2 off 2" *50ft rolls and it was just enough to wrap the exhausts.

Here are the contact details, or you can visit www.designengineering.com

Trinity Performance & Thermal Control
South Africa - Gauteng
27(0)72 7669613


Unit 9 Pomona Park, Pomona Road, Pomona Kempton Park
Johannesburg, GT1620
Phone:27(0)72 7669613




If you want the definition of "cool"in the dictionary you will find that photo next to it.

The advantage of this new stuff over other wraps is you don't have to wet it first, and it doesn't need any silicon spray. The two outer headers were easily done, but the centre siamese twinned headers needed some dexterity!

Having done that, I pre-assembled the muffler and connector pipe and called it a night. I had a little hassle arranging the muffler guard brackets and was totally foxed as to how they fit the pipes until I saw they had been stamped "F" "M"and "R" (Front, Middle and Rear) Once I had sussed that the rest was easy.
 

 
 
 
 
 
 
 

Tuesday, 9 July 2013

Small, but Important Tasks

It has been bloody miserable the past couple of weeks so I have resorted to doing stuff like fitting indicators to the nosecone, deflector hinges to windscreen uprights etc etc. All stuff that can be done indoors.

The one thing that cannot be done indoors is laying out and fitting the Alphamax Engine Management System harness.

This was easier than I thought, and in a couple of hours I had connected up the injectors, RPM sensor, fuel pump etc etc. The instructions are very clear and the connector labelling is excellent.

Then went a bit overboard with the cable ties, methinks.

Tuesday, 18 June 2013

Scuttle Butt


The one thing I was not too happy about the spray job was the painters did not spray the firewall, I think they misinterpreted my instructions. Upshot was the wall where the washer bottle, radiator overflow bottle and the brake and clutch reservoirs was bright aluminium.

Off to the local Midas Auto hardware to pick up a tin of Signal Red Duco. I was figgering the colour would not be a total match for Ferrari Red, but I was surprised how close it was. A couple of coats and hey presto!


Original Ferrari Red on top, Signal Red on the wall - a slight difference - Signal Red is "Orangier". Here is the washer bottle bracket and zooty Stainless Steel capscrews nestling in their rivnuts - you can see the overflow bottle rivnut mounts to the right.

Monday, 17 June 2013

Huffing and puffing .... Not!!

So I head down to my favourite glue merchant but it being a public holiday in South Africa the shop is shut. So no chance to get in some thoroughly legal glue sniffing and incidental carpet fitting today. I did pick up a brand new pop rivet gun to replace my mangy old one, as well as 3 bottles of brake fluid.

So instead of doing carpets I decide to fit the stoneguards, which was pretty hectic because it involved me having to drill into my lovely red mudguards. Not a difficult job but be careful and have some extra pop rivets and washers on hand because sometimes you have to drill out one or two (OK five, if you insist on the amount). I forgot to put on the edge rubber both times!!



Having completed both sides the next move was to install the centre console. Again the rivnut tool was broken out and 4 rivnuts strategically placed - two on either side of the prop shaft tunnel. At this point I fitted the two safety belt stalks (loosely). They are not the type that has an electrical warning connection so the wires in the loom have been terminated and the seatbelt warning light will not feature on the console.


Having satisfied the mechanical urge to bolt stuff together I turned to the exhaust headers and muffler. I have elected to wrap the headers in DEI titanium lagging which is supposed to have some benefit power wise because it keeps the exhaust system running hotter. Now I failed thermodynamics as a subject at 'varsity (very badly, I might add) so I am unable to verify or disprove their claims to increased power output, reduced fuel consumption and general added longevity of the engine, but I will say their product looks really good looking on a car.

So I sprayed the headers and the muffler matte black with some heat resistant paint. I think the overall effect is going to be awesome - black headers wrapped in a gunmetal fiber set off with stainless steel hoseclamps and a red perforated exhaust shield.

I then called it quits for the day, and cleaned up all the pesky pop rivet wires, then my tools. It is starting to come together, I think. But there is a lot to do yet.

I am going to get a professional to do my wiring. When the car arrived all the wires had neat little tags on them saying what went where. After a year the tags are all faded!